WUXI XINDU TELEMECANIQUE CO.LTD

High quality products, professional services, is the core supplier of the clutch industry!

Home > News > Content
What Are The Causes Of The Excessive Wear And Tear Of The Royalstar Clutch?
- Aug 31, 2017 -



What are the causes of the excessive wear and tear of the Royalstar Clutch?

There are several reasons why the Royalstar Clutch is wearing too fast.

(1) the Royalstar Clutch driven disc and the engine flywheel and the Royalstar Clutch platter slide. For example, there are individual drivers often habitual royal put the foot on the clutch pedal, the clutch pedal force, traction clutch cable, royal royal valve mechanical clutch button, button valve in abnormal working state, deflated the Royalstar Clutch booster cylinder are not normal working state, the Royalstar Clutch appeared similar to the status of the half clutch. The pressure of the Royalstar Clutch pressure plate is partially absorbed and the Royalstar Clutch is skidded, which can cause the Royalstar Clutch to wear off the friction plate of the disc.

(2) unskilled operation. Due to the lack of familiarity with the stalls of the steyer series, the structure of the Royalstar Clutch and the braking performance of the car are not fully understood, and the Royalstar Clutch is used too frequently. If you encounter a common obstacle, you can use the air brake, but you are not familiar with the braking system of the vehicle. After braking, it is necessary to start again, frequently using the Royalstar Clutch, causing wear and tear. Due to the lack of proficiency in the file, it will not be able to hang onto the file, so it will be used too frequently and wear too fast.

(3) the method of conjugation and separation is not correct. Use the Royalstar Clutch, bad cooperation, due to the throttle and gear shift gear sound, due to the impact and royal separation clutch, cause unnecessary separation, joint number increase, the wear faster. In operation, the separation is often very fast, and the joint is very slow, so that the time of the Royalstar Clutch sliding in the process of joining is lengthened and the wear is accelerated.

(4) hit the gas pedal and raise the Royalstar Clutch. Car is occurred in the car or the road, through the difficult, not using differential lock to enhance capacity, but fierce detonation throttle, heavily Royalstar Clutch, is precipitating method, caused the Royalstar Clutch platen by the impact force is too large, short time overload, causing wear too fast.

(5) severe overloading. The overload has increased the workload of the Royalstar Clutch and the Royalstar Clutch has worn too fast. There are severe overloading of individual users, resulting in the poor working conditions of the Royalstar Clutch, and accelerated wear and tear.

(6) problems of maintenance quality. Some users in the clutch plate after severe wear, USES his way to replace the lining, because of the quality of the riveting and Royalstar Clutch damage of quality problems also arise too fast. Royalstar Clutch

(7) the Royalstar Clutch disc failure. The Royalstar Clutch pressure plate overheats in use, causing the spring of the Royalstar Clutch pressure plate to change, weaken and break. Because of the spring force change, make the flywheel, driven disk and pressure plate slide, and causes the disc friction plate to increase. If the pressure plate overheats, it is best to check the spring force of the pressure plate to ensure the best joint.

The scope of its use is different, it has a very large role, and the penetration rate is very wide. The operation of the Royalstar Clutch requires a certain environment so that its maximum performance can be played out. Because the Royalstar Clutch is in different host products in combination with other products are used together, so its work environment is a bit complicated, will be affected by the influence of temperature, water, dust and other aspects. When selecting the Royalstar Clutch, you must consider the actual situation in terms of these aspects. If the clutch is to use in different environment, such as high temperature, low temperature, acid and alkali, don't choose to connect to elastic component of flexible and should choose metal flexible Royalstar Clutch of elastic element. In a small or driven drive system, the accuracy of the Royalstar Clutch is very high, so it is best to choose the non-metallic elastic element Royalstar Clutch. Some occasions their accuracy demand is different, everybody must study first. Therefore, the working environment of the Royalstar Clutch is also required. It should be used in conjunction with other components, like a pulley wheel, and be careful when choosing.